Jbl CONTROL NOW Manual do Utilizador Página 1

JBL CONTROL NOW™JBL CONTROL NOW™AWJBL®CONTROL®SERIESOWNER’S GUIDE®JBLP2605_CN_CNAW_PM-OM 4/23/08 12:57 PM Page 1

10HALF-ROUND WALL-MOUNTING(HORIZONTAL OR VERTICAL)NOTE: Decide whether you will connect the speakers as a single channel or two separate channels, and

115. The mounting bracket is designed to trap the flange of the JBL Control NOWspeaker by securing the mounting-bracket cap with two screws through th

12CONNECT AS TWO CHANNELSCAUTIONThe customer is responsible for proper selection and use of mounting hardware(available through hardware stores), to p

134. The mounting bracket is designed to trap the flange of the JBL Control NOWspeaker by securing the mounting bracket cap with two screws through th

3/4-ROUND WALL-MOUNTINGCAUTIONThe customer is responsible for proper selection and use of mounting hardware(available through hardware stores), to pro

154. Connect the small end of the multiunit wiring adapter to the rear of speaker 1, as shown.5. The mounting bracket is designed to trap the flange o

169. Place the large end of the multiunit wiring adapter that is already installed inspeaker 2 into speaker 3 by sliding a multiunit wiring adapter in

17STAND-MOUNTINGIMPORTANT SAFETY NOTE:CAUTIONThe supplied floor stand adapters facilitate installation with a variety of general-purpose floor stands

CAUTIONThe JBL Control NOW PMB Pole-Mount Bracket facilitates installation of the JBL Control NOW and JBL Control NOW AW loudspeakers with a variety o

192A. Slide the pole-mount bracket up onto the drop tube, aligning the pinholeson the bracket with those on the drop tube.(FOR SMALLER-DIAMETER DROP T

2TABLE OF CONTENTSUNPACKING THE SPEAKERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2PLACEMENT. . . . . . . . . . . . . . . . . . . . .

SPEAKER WIRING1. Use the cable assembly provided to wire the units for a single channel.Single-channel-wiring diagram. 2. Use the multiunit wiring ada

21SINGLE-CHANNEL WIRING1. Use the cable assembly provided. Run the cable assembly down the droptube; run the four sets of paired wires out through the

2-CHANNEL WIRING FOR EVEN SOUND DISTRIBUTION1. Use the even sound distribution connection for even sound distribution throughboth channels. Run the se

237. Connect the wires to the terminal assembly and place the speaker on the pole-mount bracket. Repeat this process with speaker D. Return to the ins

2-CHANNEL STEREO WIRING1. Use the stereo sound-distribution connection for a smaller home theater/stereo environment. Run the sets of paired wires out

257. Connect the wires to the terminal assembly and place the speaker on the pole-mount bracket. Repeat this process with speaker A. Return to the ins

26#10-32 x 2"Screws (4)Drop TubePole-Mount-Bracket CapPole-Mount BracketOnly two speakers shown herefor clarity.Place the pole-mount-bracket cove

27MAINTENANCE AND SERVICEThe enclosure may be cleaned using a soft cloth to remove fingerprints or towipe off dust.All wiring connections should be in

28JBL CONTROL NOW™JBL CONTROL NOW™AWFrequency Response (–6dB) 80Hz – 30kHzMax. Recommended Amplifier Power* 150WPower Handling (Continuous/Peak) 50W/3

Features, specifications and appearance are subject to change without notice.JBL and Bi-Radial are trademarks of Harman International Industries, Inco

3PLACEMENTJBL Control NOW speakers are perhaps the most flexible and versatile loud-speakers ever developed. There are numerous mounting options. The

4WALL SURFACE-MOUNTINGWhen deciding upon a location for the JBL Control NOW speaker, take care NOT to install the mounting bracket closer than 3"

54. The mounting bracket is designed to trap the flange of the JBL Control NOWspeaker by securing the mounting-bracket cap with two screws through the

6WALL CORNER-MOUNTINGCAUTIONThe customer is responsible for proper selection and use of mounting hardware(available through hardware stores), to prope

74. The mounting bracket is designed to trap the flange of the JBL Control NOWspeaker by securing the mounting-bracket cap with two screws through the

83. Connect the wires to the JBL Control NOW speaker.IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker conne

94. The mounting bracket is designed to trap the flange of the JBL Control NOWspeaker by securing the mounting-bracket cap with two screws through the